[Nfb-krafters-korner] Help needed suggestions

[Zimmer, Cindy]

Rubber cement

-----Original Message-----
From: nfb-krafters-korner-bounces at nfbnet.org [mailto:nfb-krafters-korner-bounces at nfbnet.org] On Behalf Of Blindhands at aol.com
Sent: Thursday, September 15, 2011 5:14 PM
To: nfb-krafters-korner at nfbnet.org
Subject: Re: [Nfb-krafters-korner] Help needed suggestions

What is it?  Where do you get it?
 
Last of all I am thinking maybe 
it needs to be tacky and I can put it on both surfaces and when I put it  
together it will glue together?  Anything out there like that?
Joyce  Kane
_www.KraftersKorner.org_ (http://www.krafterskorner.org/) 
Blindhands at AOL.com   

 
In a message dated 9/15/2011 5:49:48 P.M. Eastern Daylight Time,  
dianefilipe at peoplepc.com writes:

Mazy I  suggest E6000.
I use it for everything
D
----- Original Message -----  
From: <Blindhands at aol.com>
To:  <nfb-krafters-korner at nfbnet.org>
Sent: Thursday, September 15, 2011  3:38 PM
Subject: [Nfb-krafters-korner] Hel need  suggestionsp


>I am making these pins and I have purchased the  pin backs that are 3/4 
inch
> long.  I need to glue the pin backs  to a plastic cylinder.  So now I
> purchased a small hot glue gun  and tried that.  Well yep I seem to be 
> burning
> my  fingers if I put the glue on the cylinder and then pick up the pin   
and
> try to find where I glued it.  I can take the burnt fingers,  but if I 
> take
> too long to figure out where to put the pin  back and where the glue is, 
> the
> glue begins to cool and get  hard so it won't stick properly.
>
> So I tried Aleene's Tacky jar  glue.  This I used actually one of those
> little plastic cheese  spreaders that you get in those packages that have 
4
> crackers and the  smooth cheese you spread on the crackers.  Well I did a
> pretty  good jjob putting the glue on and the pin back.  I even did not 
get  
> too
> much glue squeezing out under the pin back, but...   When I opened up  
the 
> pin
> back to pin it on the cards I  have made up for the pins.  I guess I 
> didn't
> use enough  glue as the backs came off the cylinders.
>
> I figure I can give  crazy glue a try, but any suggestions how to not get
> the glue dripping  off the cylinder?  How to locate pin back to glue spot
> fast  enough without seeing?  And how do I do this without gluing my 
>  fingers  or
> pin or pin back to the above mentioned places?   I can easily clean the
> glue that I have used so far off the granite  counter, but I need some
> suggestions here.
>
> Help, Help,  Help!
>
> Joyce  Kane
> _www.KraftersKorner.org_  (http://www.krafterskorner.org/)
> Blindhands at AOL.com
>  _______________________________________________
> Nfb-krafters-korner  mailing list
> Nfb-krafters-korner at nfbnet.org
>  http://nfbnet.org/mailman/listinfo/nfb-krafters-korner_nfbnet.org
> To  unsubscribe, change your list options or get your account info for 
>  Nfb-krafters-korner:
>  
http://nfbnet.org/mailman/options/nfb-krafters-korner_nfbnet.org/dianefilipe%40peoplepc.com  


_______________________________________________
Nfb-krafters-korner  mailing  list
Nfb-krafters-korner at nfbnet.org
http://nfbnet.org/mailman/listinfo/nfb-krafters-korner_nfbnet.org
To  unsubscribe, change your list options or get your account info for  
Nfb-krafters-korner:
http://nfbnet.org/mailman/options/nfb-krafters-korner_nfbnet.org/blindhands%
40aol.com


_______________________________________________
Nfb-krafters-korner mailing list
Nfb-krafters-korner at nfbnet.org
http://nfbnet.org/mailman/listinfo/nfb-krafters-korner_nfbnet.org
To unsubscribe, change your list options or get your account info for Nfb-krafters-korner:
http://nfbnet.org/mailman/options/nfb-krafters-korner_nfbnet.org/cindy.zimmer%40nebraska.gov