[Nfb-krafters-korner] flag directions
Carol Osmar
osmarc at sbcglobal.net
Fri Aug 19 01:34:02 UTC 2016
Good job Ramona. I didn't write down the pattern but this sounds correct. The beads that were used were pony beads.
Carol
Sent from my iPhone
> On Aug 18, 2016, at 7:29 PM, Ramona Walhof via Nfb-krafters-korner <nfb-krafters-korner at nfbnet.org> wrote:
>
> I think I can remember, but my memory is so/so. Carol, please correct this
> if you see errors.
>
>
>
> You buy eight two-inch gold safety pins for each flag. Then you buy red,
> white, and blue beads with holes through the middle large enough to put the
> straight part of the safety pin through. . Sorry, I can't tell you what
> size the beads must be, but hopefully Carol or Theresa can. On four pins
> you place 7 beads, beginning with red and alternating colors. Then put one
> pin through the end that does not open. Do three additional pins just like
> this. Then you make three pins using red, white, red, white, and three blue
> beads. All seven pins should now be suspended from the pin across the top.
>
>
>
>
> Now you need to straighten out the top pin and slide the other seven around
> the turn which is largely straightened out. When they are all around, you
> bend the top pin back so that it can be fastened. As you look at the pin,
> you should have three beads across and three blue beads up and down at the
> right top of the flag. There should be four red stripes and three white
> stripes up and down with the red on top and bottom and alternating with the
> white. These pins are all hanging loose from the top pin. The top pin can
> be attached to a shirt with its fastener at the left as you wear the flag.
>
> After reading this over, I am wondering if we really used 7 beads on each
> pin or six. It mayh be that we could only fit six beads, so the top red
> bead would be eliminated, and the white stripe in the middle would only go
> on the first four pins.
>
> It took some people longer than others of course, but they liked the
> project. You have to sort the colors ahead of time in different containers
> which should be open and flat so crafters can pick up the beads easily. We
> had anywhere between 2 and 8 people working at the same time, and we just
> had to pass the bead containers back and forth. That was one of my jobs.
> Ed Osmar also handled this project, but he and Carol bought the stuff and
> really worked out the final design.
>
> I hope my directions make sense.
>
> Ramona
>
> _______________________________________________
> Nfb-krafters-korner mailing list
> Nfb-krafters-korner at nfbnet.org
> http://nfbnet.org/mailman/listinfo/nfb-krafters-korner_nfbnet.org
> Division Website: http://www.krafterskorner.org
> Facebook page: https://www.facebook.com/pages/NFB-Krafters-Division/269246643109571
> Krafters-Korner Blog https://craftingblind.wordpress.com/
> "Follow NFB Krafters Korner on Twitter: Our Handle is @craftingblind
> Don't have a Twitter account? You can still follow Krafters Korner on Twitter. Go to: Twitter.com/craftingblind
> To unsubscribe, change your list options or get your account info for Nfb-krafters-korner:
> http://nfbnet.org/mailman/options/nfb-krafters-korner_nfbnet.org/osmarc%40sbcglobal.net
More information about the NFB-Krafters-Korner
mailing list